after you apply the give configurations to R1 and R2 you notice that OSPFv3 fails to start Which reason for the problem is most likely true ? A. The area numbers on R1 and R2 are mismatched B. The ...
Which three statements describe the reasons large OSPF networks use a hierarchical design? (Choose three.)
Which three statements describe the reasons large OSPF networks use a hierarchical design? (Choose three.) A. to confine network instability to single areas of the network. B. to reduce the comple ...
Which functionality does an SVI provide?
Which functionality does an SVI provide? A. OSI Layer 2 connectivity to switches B. remote switch administration C. traffic routing for VLANs D. OSI Layer 3 connectivity to switches Correct A ...
If two OSPF neighbors have formed complete adjacency and are exchanging link-state advertisements, which state have they reached?
If two OSPF neighbors have formed complete adjacency and are exchanging link-state advertisements, which state have they reached? A. Exstart B. 2-Way C. FULL D. Exchange Correct Answer: C T ...
Which two statements about RIPv2 are true? (Choose two)
Which two statements about RIPv2 are true? (Choose two) A. It must be manually enabled after RIP is configured as the routing protocol B. It uses multicast address 224.0.0.2 to share routing inform ...
Given the output from the show ip eigrp topology command, which router is the feasible successor?
Refer to the exhibit. Given the output from the show ip eigrp topology command, which router is the feasible successor? A. 10.1.0.1 (Serial0), from 10.1.0.1, Send flag is 0x0 Composite metric is ( ...
Which IPv6 routing protocol uses multicast group FF02::9 to send updates?
Which IPv6 routing protocol uses multicast group FF02::9 to send updates? A. static B. RIPng C. OSPFv3 D. IS-IS for IPv6 Correct Answer: B Explanation Explanation/Reference: Below list ...
Which command must you enter to enable OSPFV2 in an IPV4 network?
Which command must you enter to enable OSPFV2 in an IPV4 network? A. ip ospf hello-interval seconds B. router ospfv2 process-id C. router ospf value D. router ospf process-id Correct Answer: ...
Which two steps must you perform on each device that is configured for IPv4 routing before you implement OSPFv3?(Choose two)
Which two steps must you perform on each device that is configured for IPv4 routing before you implement OSPFv3?(Choose two) A. configure an autonomous system number B. configure a loopback interf ...
When running OSPF, What would cause router A not to form an adjacency with router B?
Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B? A. The loopback addresses are on different subnets. B. The value of the dead timers on th ...
Which Command do you enter so that R1 advertises the loopback0 interface to the BGP Peers?
Refer to the exhibit . Which Command do you enter so that R1 advertises the loopback0 interface to the BGP Peers? A. Network 172.16.1.32 mask 255.255.255.224 B. Network 172.16.1.0 0.0.0.255 C. N ...
Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?
Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1? A. The router will forward packets from R3 to R2 to R1. B. The rout ...
Which option describes a difference between EIGRP for IPv4 and IPv6?
Which option describes a difference between EIGRP for IPv4 and IPv6? A. Only EIGRP for IPv6 advertises all connected networks. B. Only EIGRP for IPv6 requires a router ID to be configured under th ...
Which definition of default route is true?
Which definition of default route is true? A. A route that is manually configured. B. A route used when a destination route is missing. C. A route to the exact /32 destination address D. Dynam ...
Which value must you configure on a device before EIGRP for IPv6 can start running?
Which value must you configure on a device before EIGRP for IPv6 can start running? A. public IP address B. loopback interface C. router ID D. process ID Correct Answer: C Have you learned ...